What Sets Our ASTM A516 Gr 70 Plates Apart?
Mill-Certified Heats
Killed, fine-grain plate sourced with full heat traceability
IBR and PED Approved
Boiler and pressure-vessel plate cleared for statutory use
UT and Impact Tested
Ultrasonic, Charpy V-notch and HIC testing on request
Cut-To-Size In One PO
Plain plate, profile-cut or ring blanks from a single enquiry
Quote In 24 Hours
Ready stock thickness ships the same week
ASTM A516 Gr 70 Plate Overview
- 1Type: Boiler Quality, Pressure Vessel, Normalized, HIC-Tested, Cut-To-Size
- 2Thickness Range: 6 mm – 150 mm • Width up to 2500 mm
- 3Common Grades: ASTM A516 Gr 70, ASME SA516 Gr 70, A516 Gr.70N
- 4Condition: As-Rolled, Normalized, Killed and Fine-Grain Practice
- 5Standards: ASTM A516/A516M, ASME SA516, EN 10028-2, IBR Chapter IV
- 6Origin: Indian origin • European origin • Korean origin
Or call our Mumbai office: +91 22 6743 7134 • Fast dispatch on ready stock thickness
ASTM A516 Grade 70 is top carbon steel. It handles low temperatures and high pressure. The balanced carbon manganese alloy gives high tensile strength. Refineries and fabricators rely on this tough material. Ganpat Industrial normalizes and tests every single plate. All plates strictly meet ASME SA516 Section II. Your mill certificates always match code requirements. Fabricators choose Grade 70 for boilers and vessels. Standard structural plates cannot match these verified specifications. Ganpat Industrial brings over 25 years of trust. We supply custom cut orders and ready stock. Deliveries reach buyers across India Middle East Africa.
Mumbai · ASTM A516 Gr 70 Plate Manufacturer India
ASTM A516 Gr 70 Plates Built To Hold Pressure When Ordinary Carbon Steel Can’t
Ganpat Industrial rolls and supplies ASME SA516 Grade 70 / A516 Gr.70N Plates for boiler shells, pressure vessels, LPG bullets and separator skids across India, the UAE and the Middle East.
- ✓ISO 9001:2015
- ✓PED 2014/68/EU
- ✓IBR Approved
- ✓ASME Certified
- ✓Third-Party Inspected
Cut to Size ASME SA 516 Gr 70 Carbon Steel Plate Supplier in India With As-rolled Or Normalized Condition
ASTM A516 Gr 70 Plate Specification
ASTM A516 Gr 70 Plate Material
- UNS K02700
- ASME SA516
- ASTM A516
- Killed, Fine-Grain Practice
ASME SA 516 Gr 70 Plate Testing
- Ultrasonic Testing (UT)
- Charpy V-Notch Impact
- HIC / NACE MR0175
- Third-Party Inspection
A516 Grade 70 Plate Origin
- Indian Origin
- European Origin
- Korean Origin
- Traceable To Heat Number
Carbon Steel A516 Grade 70 Plate Size Range
- Thickness: 6 – 150 mm
- Width: Up To 2500 mm
- Length: Up To 12000 mm
- Custom sizes on drawing
Steel A516 Gr.70 Plate Documentation
- Mill Test Certificate 3.1
- NABL Lab Report
- Packing List
- Certificate Of Origin
SA 516 70N Plate Surface Finish
- Hot Rolled Mill Finish
- Shot Blasted
- Primer Coated
- Cut Edge / Mill Edge
ASME SA 516 Gr 70 Boiler Plate Size Chart
Standard Thickness • Width • Length
Thin Gauge
6-10 mm
Skid and panel work
Medium Gauge
12-25 mm
Tank and shell courses
Heavy Gauge
32-50 mm
Vessel heads and nozzles
Extra Heavy
Up to 150 mm
Forged-plate applications
Standard Sheet Sizes (Width × Length)
| Thickness (mm) | Width (mm) | Length (mm) | Standard |
|---|---|---|---|
| 6 – 12 | 1500 / 2000 | 6000 / 12000 | ASTM A516 |
| 16 – 25 | 2000 / 2500 | 6000 / 12000 | ASME SA516 |
| 32 – 50 | 2000 / 2500 | 6000 / 12000 | ASME SA516 |
| 60 – 150 | Up to 2500 | Up to 10000 | On Request |
Cut-to-size, ring and profile-cut blanks available as a Supplier in India for direct fabrication.
Looking For A516 Gr 70 Plate Cut To Your Exact Drawing?Send your dimensions and we’ll come back with a factory-price quote inside 24 hours.
Discover A516 Gr.70 PVQ Plate Stock Online Tested With Charpy Impact and Ultrasonic Test At Lowest Price
ASTM A516 Gr 70 CS Plate Price List and Ready Stock
Every quote from this Supplier in India is thickness, quantity and test-package specific – here’s what moves the number.
Ready Stock: 6-50 mm In Mumbai WarehouseSame-week dispatch on standard gauges – heavier and custom sizes rolled to order.
Types Of ASTM A516 Gr 70 Plate
ASME SA 516 Gr 70 Boiler Quality Plate
IBR Chapter IV compliant plate for boiler drum and shell fabrication.
IBR Ch. IV
ASTM A516 Grade 70 Pressure Vessel Steel Plate
ASME Section VIII rated plate for heads, shells and nozzle courses.
ASME Sec VIII
A516 Grade 70 Steel Hot Rolled Plate
Supplied in as-rolled condition for general fabrication work.
As-Rolled
LTCS Grade 70 Normalized Plate
Grain-refined heat treatment for improved low-temperature toughness.
Grain Refined
A516 Gr.70 Killed Carbon Steel Plate
Fully killed melting with fine-grain practice for consistent quality.
Fine-Grain
SA 516 70N Cut-To-Size Plate
Profile and ring blanks cut to your drawing specifications.
Profile Cut
Buying A516 Gr 70 In Bulk Tonnage?Container-load orders ship under one consolidated mill certificate.
Steel A516 Gr.70 Hot Rolled Plate Weight Chart
Theoretical weight per square metre at 7.85 g/cm³ density – a Manufacturer in India reference for freight and MTO planning.
6 mm
47.1 kg/m²
10 mm
78.5 kg/m²
16 mm
125.6 kg/m²
20 mm
157.0 kg/m²
25 mm
196.3 kg/m²
32 mm
251.2 kg/m²
40 mm
314.0 kg/m²
50 mm
392.5 kg/m²
Application Of ASTM A516 Gr 70 Pressure Vessel Steel Plate
Selected wherever a code inspector signs off on both strength and low-temperature toughness – sourced from a Supplier in India.
Boiler Shells and Drums
Pressure Vessels
LPG and Propane Bullets
Storage Tanks
Heat Exchangers
Separator Skids
Oil and Gas Equipment
Power Plant Fabrication
Carbon Steel A516 Grade 70 Boiler Quality Plate Pressure Rating
ASME Section II-D allowable stress values used to set design pressure for each shell course.
Allowable Stress @ 38°C
138 MPa
ASME II-D
Allowable Stress @ 343°C
124 MPa
ASME II-D
Max Design Temperature
400°C
Typical Limit
Hydrotest Factor
1.3× MAWP
Code Practice
Sizing A Pressure-Vessel Shell Course In A516 Gr 70?Share your thickness, diameter and MAWP and we’ll verify code compliance.
SA 516 70N Rolled Plate Thickness Schedule
Full range extends to 150 mm; intermediate gauges rolled on request as a Manufacturer in India.
A516 Gr.70 Killed Carbon Steel Chemical Composition
Values per ASTM A516/A516M for plate up to 65 mm; heavier gauge bands vary slightly – confirm on the MTC.
Want To Review The Complete Heat Analysis First?The MTC 3.1 chemistry sheet is available on request before you commit.
ASME SA 516 Gr 70 Carbon Steel Plate Mechanical Properties
Tensile Strength
485-620 MPa
ASTM A516
Yield Strength, Min
260 MPa
≤65 mm
Elongation, Min
21 %
In 50 mm
Hardness, Typical
137-187 HBW
Non-Mandatory
ASTM A516 Grade 70 Plate Material Equivalent
North American
- ASME SA516 Gr 70
- ASTM A516 Gr 70
- CSA G40.21 44W
European
- EN 10028-2 P265GH
- DIN 17155 HII
- NF A36-205 A48AP
Asian
- JIS G3106 SM490
- GB 713 Q345R
- IS 2002 Grade 2
Not Sure How Your Local Grade Maps To A516 Gr 70?We’ll cross-check it against ASME SA516 Gr 70 before you place the order.
ASTM A516 Grade 70 Plate Delivered Weekly to the Following Countries
| Export to | Countries | Continent | Shipping time | Ports |
|---|---|---|---|---|
 |
Kuwait | Asia | 10 days | Shuaiba |
 |
Nigeria | Africa | 30 days | Calabar |
 |
Netherlands | Europe | 30 days | Manila |
Monthly Delivery of ASTM A516 Grade 70 Plate to Below Countries
| Export to | Countries | Continent | Shipping time | Ports |
|---|---|---|---|---|
 |
Colombia | South America | 45 days | Buenaventura |
 |
Morocco | Africa | 45 days | Tanger Med |
Ready To Lock In A Firm Price On A516 Gr 70?Tell us the thickness, quantity and destination port for a same-day quote.
Frequently Asked Questions
Is ASTM A516 Gr 70 the same as ASME SA 516 Gr 70?
Yes. ASME SA 516 mirrors ASTM A516 with added Boiler and Pressure Vessel Code requirements.
Does A516 Grade 70 need normalizing?
Only when the design code, thickness or service temperature calls for it – confirm on your purchase specification.
Can Carbon Steel Plate be supplied HIC tested?
Yes, sour-service HIC / NACE MR0175 testing is available on request for sour-gas duty.
What is the minimum order quantity?
Ganpat Industrial supplies from single-plate trial orders to full container loads – share size and quantity for a factory price.
Material Inspection Facilities in the Following Continent
| Continents | Country |
|---|---|
| Africa | Nigeria, Egypt, South Africa, Kenya, Ghana, Ethiopia |
| North America | United States, Canada, Mexico, Cuba |
| South America | Brazil, Argentina, Colombia, Chile, Peru |
| Asia | India, Japan, South Korea, Indonesia, Saudi Arabia, Iran |
| Europe | Germany, France, UK, Italy, Spain, Poland, Ukraine |
| Australia | New Zealand, Papua New Guinea, Fiji, Samoa |
6 Reasons to choose Ganpat Industrial Corporation
- Distributor of Heat Exchanger parts and Alloys for High Temperature applications.
- Stockholder and importer of Ferrous and non ferrous metals.
- Wide stock of prime quality austenitic and Ferritic Stainless Steel for Extreme pressure environment.
- Marine grade steel at lowest price in Mumbai.
- Compare Price per KG in India and China.
- Offer Resale price to local suppliers, traders and wholesalers in UAE, Saudi Arabia, Egypt, and USA