Why Furnace And Chemical Plant Buyers Send Inconel 600 Angle Enquiries To Ganpat Industrial
Cut To Your Fabrication List
6 m bars or sawn sizes, you pay only for metal used
72% Minimum Nickel
True N06600 chemistry, PMI verified before loading
Built For 1093°C Service
Oxidation resistance where stainless simply scales away
3.1 MTC On Every Bundle
Heat number stamped and matched to the certificate
Quoted Within 24 Hours
Send the size list and get a landed rate next working day
Inconel 600 Angle Overview
- 1Profile: Equal Leg Angle, Unequal Leg Angle, Channel, U Channel, C Channel, I Beam, H Beam, Chain
- 2Equal Leg: 25 x 25 x 3 mm up to 200 x 200 x 15 mm
- 3Unequal Leg: 45 x 25 x 4 mm up to 200 x 150 x 15 mm
- 4Grade Marks: UNS N06600, WNR 2.4816, Alloy 600, Nickel 600, Sanicro® 70
- 5Specification: ASTM B166, ASME SB-166, ASTM B168, AMS 5665
- 6Condition: Annealed, pickled, non-magnetic
Mumbai desk: +91 22 6743 7134 • Ready-stock sizes loaded the same week
Inconel 600 Angle resists high heat and extends frame life. It contains over 72 percent nickel and 14-17 percent chromium. This material withstands temperatures up to 1093°C. High nickel content prevents chloride stress corrosion cracking. It is used in furnace muffles and retort supports. Standard stainless angles would scale and sag quickly. Ganpat Industrial provides custom-cut lengths for your needs. The material comes annealed and pickled with certified quality. Every bundle includes an EN 10204 3.1 certificate and PMI confirmation.
Mumbai · Inconel 600 Angle Manufacturer and Exporter India
Inconel 600 Angle For Furnace Fixtures And Chloride Service Where Stainless Scales Away
We stock and cut Inconel 600 Angle in UNS N06600 / WNR 2.4816, equal and unequal leg. Shipped across India, the Gulf and Africa.
- ✓ISO 9001:2015
- ✓ISO 14001:2015
- ✓OHSAS 18001:2007
- ✓PED Certified
- ✓NABL Tested
Alloy 600 Channel Manufacturer in India With Size 40*20mm to 300*300mm With MTC
Inconel 600 Angle Specification
Everything buyers usually chase over email is listed here.
Inconel 600 Angle Grade Marks
- UNS N06600
- WNR 2.4816
- Alloy 600 / Nickel 600
- Sanicro® 70
Alloy 600 Equal Leg Angle Standard
- ASTM B166 / ASME SB-166
- ASTM B168 (plate origin)
- AMS 5665
- EN 10056-1 section dims
UNS N06600 Unequal Leg Angle Range
- Equal: 25x25x3 to 200x200x15
- Unequal: 45x25x4 to 200x150x15
- Thickness: 3 mm to 15 mm
- Larger sections to drawing
WNR 2.4816 Angle and Channel Length
- 3 m, 4 m, 5 m or 6 m bars
- 6000 mm is the stock length
- Tolerance minus 0 plus 100 mm
- Cut lengths to your list
Nickel Alloy 600 Angle Delivery Condition
- Annealed from about 982°C
- Air cooled or water quenched
- Pickled and descaled
- Not age hardening
Inconel Alloy 600 Angle and I Beam Testing
- PMI on every bundle
- Tensile and hardness
- Chemical analysis to ASTM B880
- Third-party inspection
Nickel 600 Angle Surface Finish
- Annealed and pickled
- Shot blasted
- Grit 180 / 320 polish
- Mill finish
Sanicro® 70 Angle and C Channel Origin
- Indian origin
- European origin
- Japanese and US origin
- Traceable to heat number
Inconel 600 H Beam and U Channel
- Fabricated from B168 plate
- Parallel flange U channel
- Tapered flange C channel
- Section list against drawing
Alloy 600 Equal Leg Angle Size Chart
Section area drives weight and price. Root radius affects fit-up against a flat plate.
Equal Leg
25-200 mm
Leg length range
Unequal Leg
45×25-200×150
Long leg x short leg
Thickness
3-15 mm
Standard stocked band
Bar Length
6000 mm
Minus 0, plus 100 mm
| Designation A x A x t | Leg A (mm) | Thickness t (mm) | Root Radius r (mm) | Section Area (cm²) |
|---|---|---|---|---|
| 25 x 25 x 3 | 25 | 3 | 3.5 | 1.42 |
| 25 x 25 x 5 | 25 | 5 | 3.5 | 2.26 |
| 30 x 30 x 3 | 30 | 3 | 5 | 1.74 |
| 30 x 30 x 5 | 30 | 5 | 5 | 2.78 |
| 40 x 40 x 4 | 40 | 4 | 6 | 3.08 |
| 40 x 40 x 6 | 40 | 6 | 6 | 4.48 |
| 50 x 50 x 5 | 50 | 5 | 7 | 4.80 |
| 50 x 50 x 6 | 50 | 6 | 7 | 5.69 |
| 60 x 60 x 6 | 60 | 6 | 8 | 6.91 |
| 65 x 65 x 8 | 65 | 8 | 9 | 9.85 |
| 75 x 75 x 6 | 75 | 6 | 9 | 8.73 |
| 75 x 75 x 10 | 75 | 10 | 9 | 14.09 |
| 80 x 80 x 8 | 80 | 8 | 10 | 12.27 |
| 90 x 90 x 9 | 90 | 9 | 10 | 15.50 |
| 100 x 100 x 8 | 100 | 8 | 12 | 15.51 |
| 100 x 100 x 10 | 100 | 10 | 12 | 19.15 |
| 125 x 125 x 12 | 125 | 12 | 12 | 28.71 |
| 150 x 150 x 12 | 150 | 12 | 12 | 34.71 |
| 150 x 150 x 15 | 150 | 15 | 2 | 42.75 |
| 200 x 200 x 15 | 200 | 15 | 2 | 57.75 |
Your Inconel Alloy 600 Angle Section Is Missing From The Chart?Mail the drawing today, our fabrication desk prices it tomorrow.
Buy American Origin WNR 2.4816 Beam and Chain With Painted and Mill Finish At Discounted Price
Sanicro® 70 H Beam Surface Finish
Mill finish, annealed and pickled options are kept ex-stock by a leading Manufacturer in India.
Ex-Stock Finishes
- Mill Finish – as rolled, lowest cost
- Annealed and Pickled – oxide-free skin
- Both held ready in Mumbai
Blasted and Satin
- Shot Blasted – even matt grey
- Grit 180 Polish – directional satin line
- Gives a key for welding or coating
Fine Polished
- Grit 320 Polish – finer satin
- Buffed / Mirror – high reflectivity
- Chosen where wash-down is frequent
Types of Inconel 600 Angle
Every profile below ships from the same heat and one certificate.
Inconel 600 Angle
L-section for furnace frames and hot gas ducting supports.
ASTM B166
Alloy 600 Equal Leg Angle
Both legs the same. Symmetric support and simple fit-up.
25-200 mm
UNS N06600 Unequal Leg Angle
Long and short leg. Suits one-sided loads and tight spaces.
45×25-200×150
WNR 2.4816 Channel
U-shaped section for retort supports and base rails.
Fabricated
Nickel Alloy 600 U Channel
Parallel flanges. Sits flat and clean against plate.
Parallel Flange
Inconel Alloy 600 C Channel
Tapered flanges. Lighter section for the same depth.
Tapered Flange
Nickel 600 I Beam
Narrow flange. Strong along one bending axis.
To Drawing
Sanicro® 70 H Beam
Wide flange. Carries heavy load in both directions.
Wide Flange
WNR 2.4816 Equal Leg Angle Weight Chart
Weight per metre is section area times 8.43 g/cm³. Multiply by 6 for a standard bar.
Density Used
8.43 g/cm³
0.304 lb per cubic inch
Weight Formula
A x 0.843
Area in cm² gives kg per metre
Per 6 m Bar
kg/m x 6
Standard stocked length
Lightest Stocked
1.20 kg/m
25 x 25 x 3 mm equal angle
| Size (mm) | Area (cm²) | Weight (kg/m) | Weight Per 6 m Bar (kg) |
|---|---|---|---|
| 25 x 25 x 3 | 1.42 | 1.20 | 7.20 |
| 25 x 25 x 5 | 2.26 | 1.91 | 11.46 |
| 30 x 30 x 3 | 1.74 | 1.47 | 8.82 |
| 30 x 30 x 5 | 2.78 | 2.34 | 14.04 |
| 40 x 40 x 4 | 3.08 | 2.60 | 15.60 |
| 40 x 40 x 6 | 4.48 | 3.78 | 22.68 |
| 50 x 50 x 5 | 4.80 | 4.05 | 24.30 |
| 50 x 50 x 6 | 5.69 | 4.80 | 28.80 |
| 60 x 60 x 6 | 6.91 | 5.83 | 34.98 |
| 65 x 65 x 8 | 9.85 | 8.30 | 49.80 |
| 75 x 75 x 6 | 8.73 | 7.36 | 44.16 |
| 75 x 75 x 10 | 14.09 | 11.88 | 71.28 |
| 80 x 80 x 8 | 12.27 | 10.34 | 62.04 |
| 90 x 90 x 9 | 15.50 | 13.07 | 78.42 |
| 100 x 100 x 8 | 15.51 | 13.07 | 78.42 |
| 100 x 100 x 10 | 19.15 | 16.14 | 96.84 |
| 125 x 125 x 12 | 28.71 | 24.20 | 145.20 |
| 150 x 150 x 12 | 34.71 | 29.26 | 175.56 |
| 150 x 150 x 15 | 42.75 | 36.04 | 216.24 |
| 200 x 200 x 15 | 57.75 | 48.68 | 292.08 |
| Size (mm) | Area (cm²) | Weight (kg/m) | Weight Per 6 m Bar (kg) |
|---|---|---|---|
| 45 x 25 x 4 | 2.67 | 2.25 | 13.50 |
| 50 x 30 x 5 | 3.79 | 3.19 | 19.14 |
| 50 x 40 x 5 | 4.29 | 3.62 | 21.72 |
| 60 x 40 x 5 | 4.79 | 4.04 | 24.24 |
| 65 x 50 x 6 | 6.63 | 5.59 | 33.54 |
| 75 x 50 x 8 | 9.45 | 7.97 | 47.82 |
| 90 x 65 x 8 | 11.87 | 10.01 | 60.06 |
| 100 x 65 x 8 | 12.67 | 10.68 | 64.08 |
| 100 x 75 x 10 | 16.61 | 14.00 | 84.00 |
| 125 x 75 x 10 | 19.00 | 16.02 | 96.12 |
| 150 x 90 x 12 | 27.51 | 23.19 | 139.14 |
| 150 x 100 x 15 | 35.25 | 29.72 | 178.32 |
| 200 x 100 x 15 | 42.75 | 36.04 | 216.24 |
| 200 x 150 x 15 | 50.25 | 42.36 | 254.16 |
Inconel 600 Angle Price And MOQ
Landed cost moves with LME nickel, section size and quantity – here is what sets the number.
◆MOQ: 1 Bar, No Minimum Tonnage
◆Priced Against Daily LME Nickel Print
◆Cut Lengths Priced Per Piece, Not Per Bar
Get A Firm Number In 24 HoursSend size, thickness and quantity, our desk quotes against the same-day LME print.
Nickel Alloy 600 Angle Thickness and Tolerance Chart
Leg length thickness and squareness are checked on every section by our Supplier in India.
Light Sections
3-5 mm
25×25 to 40×40 legs
Medium Sections
5-9 mm
50×50 to 90×90 legs
Heavy Sections
8-15 mm
100×100 to 200×200 legs
Squareness
90° ± 2°
Angle between the two legs
Measure Leg Length
Check both legs, not just one.
Gauge Thickness Mid-Leg
Never at the fillet, where metal runs thicker.
Confirm Squareness
Out-of-square legs cost time at weld fit-up.
Check Straightness
Bow and twist over the full bar, before cutting.
Match Heat To MTC
Stamped heat number must appear on the 3.1 certificate.
◆Or ASTM B906 On Request
◆Chemistry Checked To ASTM B880
◆Nominate Standard On The PO
Nickel Alloy 600 Angle Needed Before Your Shutdown Window?Give us the cut list and the date. We plan backwards from it.
Inconel Alloy 600 Angle Chemical Composition
Per ASTM B166 For Alloy UNS N06600
Nickel Ni
72.00 min
Chromium Cr
14.00-17.00%
Iron Fe
6.00-10.00%
Manganese Mn
≤ 1.00%
Silicon Si
≤ 0.50%
Copper Cu
≤ 0.50%
Carbon C
≤ 0.15%
Sulphur S
≤ 0.015%
Nickel 600 Angle Mechanical Properties
Annealed Condition – Specified Minimums
Tensile Strength (MPa)
≥ 550
80 ksi min
Yield Strength 0.2% (MPa)
≥ 240
35 ksi min
Elongation In 50 mm
≥ 30%
Cold Forms Well
Hardness
65-85 HRB
Annealed Bar
Mechanical Properties By Form And Condition
| Form | Condition | Tensile Strength | Yield Strength | Elongation |
|---|---|---|---|---|
| Rod & Bar | Cold-Drawn Anneal | 550-690 MPa | 170-345 MPa | 35-55% |
| Rod & Bar | Cold-Drawn As-Drawn | 725-1035 MPa | 550-860 MPa | 10-30% |
| Rod & Bar | Hot-Finished Anneal | 550-690 MPa | 205-345 MPa | 35-55% |
| Rod & Bar | Hot-Finished As-Drawn | 585-830 MPa | 240-620 MPa | 30-50% |
| Plate | Hot-Rolled Anneal | 550-725 MPa | 205-345 MPa | 35-55% |
Physical Data and Typical Annealed Bar Values
Density
8.43 g/cm³
Drives every weight on this page
Melting Range
1354-1413°C
2470-2575°F
Elastic Modulus
207 GPa
30 x 10⁶ psi at room temp
Thermal Conductivity
14.8 W/m·K
At 21°C
Thermal Expansion
13.3 µm/m·K
Measured 21-93°C
Typical Tensile
655 MPa
Annealed bar, 95 ksi
Typical Elongation
45%
Annealed bar or billet
Magnetic Response
Non-Magnetic
Not age hardening
Inconel 600 Angle Machining And Fabrication
Work-hardens fast under a light or dwelling cut, so the rules below matter more than on carbon steel.
Rigid Setup
Overpowered machine, minimal tool overhang.
Sharp Tools Only
Swap on a schedule, not after wear shows.
Positive Rake Angle
Carbide-tipped for most cuts, HSS for interrupted cuts.
Constant Feed
Never let the tool dwell, it work-hardens the surface instantly.
Soluble Coolant
Carries heat away, extends tool life on every pass.
Sanicro® 70 Angle Material Equivalent
Drawing names a national mark instead of UNS? Match it here before ordering.
ASTM / ASME
- UNS N06600
- B166 / SB-166 (Bar)
- B168 / SB-168 (Plate)
- B564 (Forgings)
EN / DIN
- WNR 2.4816
- NiCr15Fe
- DIN 17742 / 17750
BS
- NA 14
- BS 3072 to BS 3076
JIS
- NCF 600
AFNOR
- NC 15 Fe
Trade Names
- Sanicro® 70
- Alloy 600 / Nickel 600
- AMS 5665 (Bar)
Weekly Delivery Of Inconel 600 Angle To These Countries
Weekly sailings from Mumbai. Transit is port to port, after clearance.
| Country | Continent | Transit Time |
|---|---|---|
| Qatar | Asia | 7 Days |
| Malaysia | Asia | 10 Days |
| Vietnam | Asia | 10 Days |
| Brazil | South America | 45-60 Days |
Monthly Delivery Of Inconel 600 Angle To These Countries
Consolidated monthly loads. Share the discharge port for a firm date.
| Country | Continent | Transit Time |
|---|---|---|
| Egypt | Africa | 18 Days |
| Netherlands | Europe | 30 Days |
Application Of Inconel 600 Angle and U Channel
Built for where the frame lives inside the furnace.
Heat Treatment Furnace Fixtures
Retorts, Muffles and Furnace Trays
Nuclear Steam Generator Supports
Titanium Dioxide Plants
Chlorination and HCl Gas Equipment
Caustic Soda and Soap Plants
Vacuum Furnace Fixtures
Aerospace and Jet Engine Rigs
Inconel 600 Angle vs Inconel 625 Angle
The Comparison Every Buyer Runs Before Approving The Alloy
Inconel 600 Angle
- Nickel: 72% minimum
- Chromium: 14-17%
- Molybdenum: none added
- Yield Strength: ≥ 240 MPa
- Density: 8.43 g/cm³
- Best For: Furnace heat, dry chlorine, caustic
Inconel 625 Angle
- Nickel: 58% minimum
- Chromium: 20-23%
- Molybdenum: 8-10% plus Nb
- Yield Strength: much higher
- Density: 8.4 g/cm³
- Best For: Seawater, acids, high strength
◆600 Costs Less Than 625
◆Need More Oxidation? Step To Alloy 601
◆Neither Is Age Hardening
Still Weighing Sanicro® 70 Against A Cheaper Grade?One sheet, three alloy rates, zero obligation. Decide on numbers.
Inconel 600 Angle Test Certificate
EN 10204 3.1 Mill Test Certificate
Every bundle ships against a 3.1 certificate. It carries the stamped heat number, full chemistry with nickel and chromium, and that heat's tensile, yield, elongation and hardness results.
UNS N06600 Angle Material Testing
PMI, tensile, chemical and hardness checks confirm every UNS N06600 Angle heat before dispatch, backed by a trusted Supplier in India.
PMI Testing
- Checks: nickel floor and chromium band
- Scope: every bundle, before loading
- Output: alloy confirmation on file
Tensile Test
- Checks: yield, tensile, elongation
- Against: ASTM B166 minimums
- Output: values printed heat-wise
Chemical Analysis
- Checks: full heat composition
- Method: carried out to ASTM B880
- Output: certified analysis report
Hardness Test
- Checks: Rockwell B readings
- Range: 65 to 85 HRB annealed
- Output: printed on the certificate
Dimensional Check
- Checks: leg length and thickness
- Also: squareness and straightness
- Scope: measured on the full bar
Grain Size Check
- Checks: grain structure after anneal
- When: long-term furnace service
- Basis: available on request
Alloy 600 Angle Export Documentation
Mill Test Certificate 3.1
Heat-wise chemistry and mechanical results
Every Order
Packing List
Bundle-wise bar count, length and net weight
Every Order
Certificate Of Origin
Chamber attested for customs clearance
Export Orders
NABL Lab Report
Independent verification of chemistry and hardness
On Request
Nickel Alloy 600 Angle Packing and Export Crating
Edge Protection
Plastic caps and corner guards so legs arrive unbruised
Strapped Bundles
Uniform lengths banded with non-metallic strap
VCI Wrap
Moisture barrier for long sea transit
PO Marked Tags
Heat, size and PO number on every bundle tag
Inconel 600 Angle – Frequently Asked Questions
How is Inconel 600 Angle priced per kg?
LME nickel drives it, at 72% nickel minimum. Send size, thickness and tonnage – rate in 24 hours.
Which sizes can I order in Alloy 600 Angle?
Equal leg 25x25x3 to 200x200x15 mm. Unequal leg 45x25x4 to 200x150x15 mm. Stock length 6 m.
What is the per metre weight of UNS N06600 Angle?
Area in cm² x 0.843, at 8.43 g/cm³. So 50x50x5 mm is 4.05 kg/m, 100x100x10 mm is 16.14 kg/m.
Up to what temperature can WNR 2.4816 Angle work?
Oxidation resistance holds to about 1093°C. Not age hardening – strength comes from cold work.
Do you supply Nickel 600 Channel, I Beam and Chain with the angle?
Yes. Channel, U Channel, C Channel, I Beam, H Beam and Chain – same N06600 heat, one certificate.
Discover Our Ready Inventory in These Cities
Global Presence
| City | City |
|---|---|
| Texas (USA) | California (USA) |
| Al Jubail (Saudi Arabia) | Dubai (UAE) |
| Dammam (Saudi Arabia) | Abu Dhabi (UAE) |
| Riyadh (Saudi Arabia) | Houston (USA) |
| Al Khobar (Saudi Arabia) | Indiana (USA) |
6 Reasons to choose Ganpat Industrial Corporation
- Distributor of Heat Exchanger parts and Alloys for High Temperature applications.
- Stockholder and importer of Ferrous and non ferrous metals.
- Wide stock of prime quality austenitic and Ferritic Stainless Steel for Extreme pressure environment.
- Marine grade steel at lowest price in Mumbai.
- Compare Price per KG in India and China.
- Offer Resale price to local suppliers, traders and wholesalers in UAE, Saudi Arabia, Egypt, and USA