Why Project Buyers Place Repeat Orders For Inconel 718 Angle With Ganpat Industrial ?
Angle Stock On The Floor
20×20 to 200×200 mm legs held ready, quoted within 24 hours
Heat-Wise Traceability
Each length stamped to its cast and ASTM B637 test report
Cut To Your Length
Saw-cut to drawing, no minimum bundle, zero offcut waste billed
Annealed Or Aged Supply
AMS 5662 or AMS 5663 condition – you choose at PO stage
Straightness Checked
Leg squareness and camber verified before any bundle is strapped
Inconel 718 Angle Snapshot
- 1Leg Range: Equal 20×20 to 200×200 mm • Unequal 40×25 to 200×100 mm
- 2Grade: Inconel 718 • Alloy 718 • UNS N07718 • W.Nr. 2.4668
- 3Thickness: 3 mm to 25 mm • heavier sections on drawing
- 4Length: 1000 / 2000 / 3000 / 6000 mm • saw-cut to size
- 5Condition: Solution annealed, aged, hot rolled, laser cut & press braked
- 6Standards: ASTM B637, ASME SB637, AMS 5662 / 5663, ASTM B670
Mumbai desk: +91 22 6743 7134 • Send leg size, thickness and metres for a same-day rate
Ganpat Industrial Corporation supplies Inconel 718 Angle cut, rolled and finished from certified UNS N07718 stock at our Mumbai works. Alloy 718 is age hardenable, and that single fact changes what a structural angle can do: after the double-age cycle the section carries above 1275 MPa tensile while still holding shape at 700°C. Engine mounting rails, turbine casing brackets, wellhead frames and cryogenic tank supports all lean on that combination. Where a solid-solution grade would relax under bolt load at temperature, an aged 718 leg holds preload through the cycle. We stock equal leg and unequal leg profiles, cut them to your bar list, and release each bundle only after the heat number, leg squareness and section thickness are recorded. Two decades of nickel alloy trade from Mumbai now reaches buyers in the UAE, Saudi Arabia, Singapore, Europe and North America.
Mumbai · Age-Hardenable Nickel Alloy Structural Profiles
Inconel 718 Angle That Holds Bolt Load And Section Shape Where Ordinary Structural Steel Gives Up
Ganpat Industrial rolls, cuts and heat treats Inconel 718 Angle for turbine frames, wellhead skids, cryogenic supports and furnace structures – shipping equal leg and unequal leg sections to fabricators across India, the Gulf, Europe and Southeast Asia.
- ✓ISO 9001:2015
- ✓ISO 14001:2015
- ✓PED 2014/68/EU
- ✓NORSOK Certified Material
- ✓ASTM B637 Compliant
UNS N07718 L Shape Angle Stockist & Exporter Serving Aerospace and Oil Field Projects Buyers Across India
Specification Of Inconel 718 Angle
Inconel 718 Angle Grade
- UNS N07718
- W.Nr. 2.4668
- Alloy 718 / Nickel Alloy 718
- API 6A718 on request
Alloy 718 Angle Standards
- ASTM B637 / ASME SB637
- AMS 5662 & AMS 5663
- ASTM B670 (plate route)
- DIN 17742 / EN 10302
UNS N07718 Angle Leg Size
- Equal: 20×20 to 200×200 mm
- Unequal: 40×25 to 200×100 mm
- Inch: 1″ to 8″ leg
- Non-standard legs on drawing
Inconel 718 Angle Thickness
- 3 mm to 25 mm standard
- Up to 40 mm on enquiry
- Tolerance to ASTM B637
- Root radius as rolled
Alloy 718 Angle Length
- 1000 / 2000 / 3000 mm
- 6000 mm stock lengths
- Saw-cut to your bar list
- Cut tolerance ±3 mm
Inconel 718 Angle Condition
- Solution Annealed (AMS 5662)
- Solution + Double Aged (AMS 5663)
- Hot Rolled
- Stress Relieved
N07718 Angle Surface Finish
- Pickled & Descaled
- Natural Mill Finish
- Ground / Machined Leg
- Shot Blasted
Inconel 718 Angle Testing
- Spectro & PMI
- Tensile + Hardness (HBW)
- IGC to ASTM G28 A
- Dye Penetrant (DPT)
Alloy 718 Angle Trade Data
- HSN 75051200
- GST 18% (India)
- EXW / FOB / CFR / CIF
- Origin: India, USA, Europe
Have A Cutting List Ready?Send leg size, thickness and running metres – you get a firm rate with MTC 3.1 the same working day.
Types Of Inconel 718 Angle We Supply
Eight profile styles move fastests from our racks. Anything outside this list is produced from ASTM B670 plate on your drawing.
Inconel 718 Equal Angle
Equal Leg
Inconel 718 Unequal Angle
Unequal Leg
Inconel 718 Angle Bar
ASTM B637
Inconel 718 L Shape Angle
L Profile
Inconel 718 90 Degree Angle
Right Angle
Inconel 718 T Shaped Angle
Tee Section
Inconel 718 Slotted Angle
Punched Slots
Inconel 718 Hot Rolled Angle
Mill Rolled
Inconel 718 Angle Size Chart And Weight Per Meter
Weights calculated at the published Alloy 718 density of 8.19 g/cm³.
| Leg A × B (mm) | Thickness (mm) | Section Area (mm²) | Weight (kg/m) | Weight (kg/6 m) |
|---|---|---|---|---|
| 20 × 20 | 3 | 111 | 0.91 | 5.46 |
| 25 × 25 | 3 | 141 | 1.15 | 6.93 |
| 40 × 40 | 5 | 375 | 3.07 | 18.43 |
| 50 × 50 | 6 | 564 | 4.62 | 27.71 |
| 60 × 60 | 6 | 684 | 5.60 | 33.61 |
| 75 × 75 | 8 | 1136 | 9.30 | 55.82 |
| 80 × 80 | 10 | 1500 | 12.29 | 73.71 |
| 100 × 100 | 12 | 2256 | 18.48 | 110.86 |
| Leg A × B (mm) | Thickness (mm) | Section Area (mm²) | Weight (kg/m) | Weight (kg/6 m) |
|---|---|---|---|---|
| 40 × 25 | 4 | 244 | 2.00 | 11.99 |
| 50 × 40 | 5 | 425 | 3.48 | 20.88 |
| 65 × 50 | 6 | 654 | 5.36 | 32.14 |
| 75 × 50 | 6 | 714 | 5.85 | 35.08 |
| 80 × 50 | 8 | 976 | 7.99 | 47.96 |
| 100 × 65 | 8 | 1256 | 10.29 | 61.72 |
| 100 × 75 | 10 | 1650 | 13.51 | 81.08 |
| 125 × 75 | 10 | 1900 | 15.56 | 93.37 |
Order Hot Rolled and Laser Cut Alloy 718 Angles to ASTM B670 at Factory Price, Custom Lengths As Per Drawing
Application Industries For Alloy 718 Angle
An Inconel 718 Angle supplier in India maintains dimensional stability under intense heat and vibration.
Jet Engine Mounting Frames
Gas Turbine Casing Brackets
Wellhead & Drilling Skids
Rocket & Launch Structures
Nuclear Reactor Internals
Cryogenic Tank Supports
Chemical Reactor Frameworks
Offshore Platform Sub-Frames
Inconel 718 Angle Chemical Composition
Nickel (+Co)Ni
50.0–55.0%
ChromiumCr
17.0–21.0%
IronFe
Balance
Niobium (+Ta)Nb
4.75–5.50%
MolybdenumMo
2.80–3.30%
TitaniumTi
0.65–1.15%
AluminiumAl
0.20–0.80%
CobaltCo
≤ 1.00%
ManganeseMn
≤ 0.35%
SiliconSi
≤ 0.35%
CopperCu
≤ 0.30%
CarbonC
≤ 0.08%
Sulphur ≤ 0.015%, Phosphorus ≤ 0.015%, Boron ≤ 0.006%. Every heat is spectro-verified and PMI cross-checked before cutting.
Mechanical Properties Of UNS N07718 Angle Bar
Minimum values for solution treated and precipitation hardened material, sections up to 63.5 mm, as required by ASTM B637.
Tensile Strength
≥ 1275 MPa
185 ksi
Yield Strength 0.2%
≥ 1034 MPa
150 ksi
Elongation
≥ 12%
In 4D
Reduction Of Area
≥ 15%
Aged
Hardness
≥ 331 HBW
Approx 35 HRC
Density
8.19 g/cm³
0.296 lb/in³
Melting Range
1260–1336°C
2300–2437°F
Elastic Modulus
200 GPa
At 20°C
Need Aged 718 Angle With A Hardness Report?We release only after tensile and HBW readings are recorded against your heat number.
Heat Treatment Of Inconel 2.4668 Angle
Alloy 718 gets its strength from ageing, not from cold work. This is the cycle behind every aged section we ship.
Solution Anneal
954–982°C, rapid cool – the AMS 5662 route for best fatigue
High Solution Option
1038–1066°C when creep and rupture life lead the spec
First Age
718°C held 8 hours – gamma double-prime starts forming
Furnace Cool & Second Age
Cool at 55°C/h to 621°C, total ageing time 18 hours, air cool
Verify
Hardness above 331 HBW confirms the cycle landed correctly
Order annealed if your shop still has to bend, punch or weld the section – ageing is done afterwards. Order aged if the angle goes straight into assembly.
Annealed Tensile
965–1035 MPa
Soft enough to form and weld
Annealed Hardness
Approx 250 HBW
Typical solution treated reading
Aged Hardness
≥ 331 HBW
ASTM B637 minimum after double age
Service Range
−253 to 700°C
Cryogenic through hot section duty
Inconel 718 Angle vs Inconel 625 Angle
Inconel 718 Angle
- Age hardened by gamma double-prime (Ni₃Nb)
- Tensile above 1275 MPa in aged condition
- Holds bolt preload to about 700°C
- Roughly 18% iron keeps cost per kg lower
- Best fit: structural frames, brackets, skids
Inconel 625 Angle
- Solid solution strengthened by Mo and Nb
- Tensile around 827 MPa minimum, annealed
- Oxidation resistant well beyond 900°C
- Stronger against seawater pitting and crevice attack
- Best fit: exhaust ducting, marine and scrubber duty
Monthly Delivery Of Inconel 718 Angle In Below Countries
| Export to | Continent | Shipping Time |
|---|---|---|
Nigeria |
Africa | 20 Days |
Algeria |
Africa | 18 Days |
Iraq |
Middle East | 12 Days |
USA |
North America | 38 Days |
Equivalent Grades Of Nickel Alloy 718 Angle
UNS / ASTM / AMS
- UNS N07718
- ASTM B637 / B670
- AMS 5662 / 5663 / 5664
DIN / EN / WNr
- Werkstoff Nr. 2.4668
- NiCr19Fe19Nb5Mo3
- DIN 17742 / EN 10302
JIS (Japan)
- NCF 718
- JIS G4901 reference
- NCF 718 B (bar form)
GB (China)
- GH4169
- GB/T 14992 reference
- Import basis: ASTM B637
India Supply Basis
- Imported under ASTM B637
- Sections cut on drawing
- HSN 75051200
Trade Names
- Inconel® 718 (Special Metals)
- Nicrofer 5219 Nb (VDM)
- Alloy 718 / Pyromet 718
Inconel 718 Angle Weight Calculation Formula
Buyers get billed on weight, not on metres. Work it out yourself in three moves before you compare quotes.
Step 1 – Equal Angle Area
(2A − T) × T
A = leg in mm, T = thickness in mm
Step 1 – Unequal Angle Area
(A + B − T) × T
A and B are the two leg lengths
Step 2 – Weight Per Metre
Area × 8.19 ÷ 1000
Answer lands in kilograms per metre
Step 3 – Order Weight
kg/m × Total Metres
This is the figure your quote is built on
Worked example, 50 × 50 × 6 mm equal angle: area = (100 − 6) × 6 = 564 mm². Weight = 564 × 8.19 ÷ 1000 = 4.62 kg/m. A 6 metre length therefore weighs 27.71 kg, and 20 lengths come to 554 kg.
Density Used
8.19 g/cm³
Published Alloy 718 figure
Metric To Imperial
kg/m × 0.672
Converts to pounds per foot
Lengths Per Tonne
1000 ÷ kg per length
Useful for container planning
Rolling Allowance
± 3–5%
Theoretical vs actual weighbridge
Hot Rolled vs Laser Cut Inconel 718 Angle
Hot Rolled / Extruded Angle
- Continuous grain flow around the leg root
- Rounded internal radius, no weld or bend line
- Best choice for repeated load and fatigue duty
- Mill run quantity applies per size
- Typical lead time 4 to 6 weeks if not in stock
Laser Cut & Press Braked Angle
- Cut from ASTM B670 plate, then folded to 90°
- Any leg and thickness combination you specify
- No mill minimum – single piece orders accepted
- Form in annealed condition, then age if required
- Typical dispatch 7 to 10 days from plate stock
Weekly Delivery Of Inconel 718 Angle In Below Countries
| Export to | Continent | Shipping Time |
|---|---|---|
UAE |
Middle East | 6 Days |
Saudi Arabia |
Middle East | 10 Days |
Oman |
Middle East | 7 Days |
Kuwait |
Middle East | 8 Days |
Welding And Machining Of Inconel 718 L Shape Angle
Follow six shop-floor rules from your Inconel 718 Angle supplier in India to prevent cracking.
Filler Metal
ERNiFeCr-2 to AWS A5.14 keeps the weld chemistry matched to the base section
Preferred Process
GTAW or electron beam, low heat input, no preheat needed on clean material
Interpass Control
Hold interpass below 150°C to avoid liquation cracking in the heat affected zone
Post Weld Treatment
Solution anneal then double age to bring the joint back to full strength
Machining Setup
Rigid clamping, positive rake carbide, flood coolant, steady feed – never dwell
Cold Forming
Bend only in annealed condition, inner radius at least twice the thickness
Inconel 718 Angle Price, MOQ And Delivery Time
Nickel alloy rates move with LME nickel and niobium, so we quote fresh each time rather than publishing a stale list.
Ready Stock Sizes
3–5 Days
Cut, tested and packed for dispatch
Plate-Cut Sections
7–10 Days
Laser cut and press braked to drawing
Mill Rolled Order
4–6 Weeks
Non-stock legs produced to schedule
Trial Order MOQ
One Length
Sample piece accepted before bulk
Send leg size, thickness, condition and total metres. You get a per-kilogram rate, weight breakup and delivery date inside one working day.
Inconel 718 Angle Test Certificates
Trust an Inconel 718 Angle manufacturer in India executing nine checks before final dispatch.
Chemical Analysis
Spectro reading of Ni, Cr, Nb, Mo and Ti against ASTM B637 limits
PMI Verification
Handheld positive material identification on each cut length
Tensile Test
Room temperature pull to confirm 1275 MPa and 1034 MPa minimums
Hardness Test
Brinell reading proves the ageing cycle actually took effect
IGC Test
ASTM G28 Method A screening for intergranular attack
Dimensional Check
Leg length, thickness, squareness and camber recorded per bundle
Dye Penetrant
Surface crack detection on cut ends and formed corners
Micro & Macro
Grain size and structure check on aged sections when specified
Third-Party Witness
SGS, BV, TUV or Lloyds inspection arranged on request
Export Documentation Set For UNS N07718 Angle
Commercial Invoice
PO matched, with HSN 75051200 and GST breakup
Every Order
Packing List
Bundle-wise length count, net and gross weight, marks
Every Order
Certificate Of Origin
Chamber attested for customs and duty clearance
Export Orders
Heat Treatment Chart
Furnace graph for the solution and double ageing cycle
Aged Supply
Fumigation & ISPM-15
Issued for wooden crate and pallet shipments
Sea Freight
Quality Assurance Plan
QAP and WPS / PQR submitted for approval before production
On Request
Regular Dispatch Of Inconel 718 Angle To These Countries
| Export To | Continent | Transit Time |
|---|---|---|
United Arab Emirates |
Asia | 6 Days |
Netherlands |
Europe | 22 Days |
Nigeria |
Africa | 28 Days |
Egypt |
Africa | 15 Days |
Italy |
Europe | 24 Days |
Air freight on part loads is arranged for urgent shutdown requirements.
Inconel 718 Angle Bar Packaging
Long sections travel badly when packed carelessly. Five layers protect the leg edges and the paperwork.
Edge & Corner Protection
Plastic caps on cut ends, sleeves along the leg tips to stop nicks
VCI Wrap
Vapour barrier film against humidity on long sea legs
Size-Wise Bundling
Strapped by leg size with heat number tag fixed to each bundle
ISPM-15 Wooden Crate
Fumigated and stamped crates or pallets for container loading
Shipping Marks
PO, grade, size, heat number, net and gross weight, destination port
Inconel 718 Angle Frequently Asked Questions
What is the largest Inconel 718 Angle you can supply?
200 × 200 mm legs up to 25 mm thick as standard. Heavier sections are machined or plate-fabricated to your drawing.
Should I order annealed or aged Inconel 718 Angle?
Annealed if your shop will bend, punch or weld it. Aged if the section is bolted straight into the assembly.
Is Inconel 718 Angle magnetic?
Practically non-magnetic at room temperature in solution annealed condition, with relative permeability close to 1.001.
Are UNS N07718 and 2.4668 the same material?
Yes. One is the American UNS number, the other the German Werkstoff number for the same alloy.
What is the maximum service temperature?
Around 700°C for load-bearing duty, and down to −253°C for cryogenic supports.
Do you accept a single-length trial order?
Yes. One cut length is accepted for trial, with the same MTC 3.1 issued as on a bulk order.
We Collaborate With Traders in the Following Cities
| Trading City | Trading City |
|---|---|
| Texas (USA) | California (USA) |
| Al Jubail (Saudi Arabia) | Dubai (UAE) |
| Dammam (Saudi Arabia) | Abu Dhabi (UAE) |
| Riyadh (Saudi Arabia) | Houston (USA) |
| Al Khobar (Saudi Arabia) | Indiana (USA) |
6 Reasons to choose Ganpat Industrial Corporation
- Distributor of Heat Exchanger parts and Alloys for High Temperature applications.
- Stockholder and importer of Ferrous and non ferrous metals.
- Wide stock of prime quality austenitic and Ferritic Stainless Steel for Extreme pressure environment.
- Marine grade steel at lowest price in Mumbai.
- Compare Price per KG in India and China.
- Offer Resale price to local suppliers, traders and wholesalers in UAE, Saudi Arabia, Egypt, and USA